OPERATING MANUAL INSTRUCCIONES DE SEGURIDAD

Please download to get full document.

View again

of 15
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Categories
Published
OPERATING MANUAL INSTRUCCIONES DE SEGURIDAD ASSEMBLY ARMADO WASH FILTERS Wash filters with cold water at least every 3 months. LAVADO DE LOS FILTROS Lave los filtros con agua fria al menos cada 3 meses.
OPERATING MANUAL INSTRUCCIONES DE SEGURIDAD ASSEMBLY ARMADO WASH FILTERS Wash filters with cold water at least every 3 months. LAVADO DE LOS FILTROS Lave los filtros con agua fria al menos cada 3 meses. REGISTER TODAY 3 easy ways to register your 5 year warranty. REGISTRE HOY 3 maneras faciles de registrarse sus 5 años de garantía. IMPORTANT SAFETY INSTRUCTIONS BEFORE USING THIS MACHINE READ ALL INSTRUCTIONS AND CAUTIONARY MARKINGS IN THIS MANUAL AND ON THE MACHINE When using an electrical appliance, basic precautions should always be followed, including the following: WARNING These warnings apply to the machine, and also where applicable, to all tools, accessories, chargers or mains adaptors. TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY: 1. This Dyson machine is not intended for use by young children or infirm persons with reduced physical, sensory or reasoning capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction by a responsible person concerning use of the machine to ensure that they can use it safely. 2. Do not allow to be used as a toy. Close attention is necessary when used by or near children. Children should be supervised to ensure that they do not play with the machine. 3. Use only as described in this Dyson Operating Manual. Do not carry out any maintenance other than that shown in this manual, or advised by the Dyson Helpline. 4. Suitable for dry locations ONLY. Do not use outdoors or on wet surfaces. 5. Do not use to pick up water. 6. Do not handle any part of the plug or machine with wet hands. 7. Do not use with a damaged cord or plug. If the supply cord is damaged it must be replaced by Dyson, its service agent or similarly qualified persons in order to avoid a hazard. 8. If the machine is not working as it should, has received a sharp blow, has been dropped, damaged, left outdoors, or dropped into water, do not use and contact the Dyson Helpline. 9. Contact the Dyson Helpline when service or repair is required. Do not disassemble the machine as incorrect reassembly may result in an electric shock or fire. 10. Do not stretch the cord or place the cord under strain. Keep the cord away from heated surfaces. Do not close a door on the cord, or pull the cord around sharp edges or corners. Arrange the cord away from traffic areas and where it will not be stepped on or tripped over. Do not run over the cord. 11. Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord. The use of an extension cord is not recommended. 12. Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they or their vapors may be present. 13. Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes. 14. Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts. Do not point the hose, wand or tools at your eyes or ears or put them in your mouth. 15. Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce airflow. 16. Use only Dyson recommended accessories and replacement parts. 17. To avoid a tripping hazard wind the cord when not in use. 18. Do not use without the clear bin and filter in place. 19. Do not leave the machine when plugged in. Unplug when not in use and before servicing. 20. Do not pull or carry by cord or use cord as a handle. 21. Use extra care when cleaning on stairs. Do not work with the machine above you on the stairs. 22. Turn off all controls before unplugging. Unplug before connecting any tool or accessory. READ AND SAVE THESE INSTRUCTIONS THIS DYSON MACHINE IS INTENDED FOR HOUSEHOLD USE ONLY 2 POLARIZATION INSTRUCTIONS To reduce the risk of electric shock, this machine has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not attempt to defeat this safety feature and do not change the plug in any way. Do not pull on the cord. Do not store near heat sources. Do not use near open flames. Do not run over the cord. Do not pick up water or liquids. Do not pick up burning objects. Do not use above you on the stairs. Do not put hands near the brush bar when the machine is in use. 3 INSTRUCCIONES DE SEGURIDAD IMPORTANTES ANTES DE UTILIZAR ESTA MÁQUINA, LEA TODAS LAS INSTRUCCIONES Y LA INDICACIONES DE PRECAUCIÓN QUE VIENEN TANTO EN ESTE MANUAL COMO EN LA MÁQUINA Cuando se usa un aparato eléctrico, deben seguirse las precauciones básicas para reducir riesgos de incendio, descarga eléctrica y lesiones personales, que incluyen lo siguiente: PELIGRO Estas advertencias se aplican a la máquina, a todas las herramientas y accesorios, así como a lo que corresponda a cualquier cargador o adaptador de alimentación. PARA DISMINUIR EL RIESGO DE PROVOCAR UN INCENDIO, RECIBIR UNA DESCARGA ELÉCTRICA O LESIONES: 1. Esta máquina Dyson no fue diseñada para que ser utilizada por niños o personas débiles con capacidades físicas, sensoriales o mentales reducidas, o que carezcan de conocimiento y experiencia al respecto, a menos que sean supervisadas o hayan recibido instrucciones por parte de una persona responsable. 2. No permita que se utilice como un juguete. Es necesaria la atención de un adulto cuando es utilizada por o cerca a un niño. Los niños deben ser supervisados para asegurarse de que no jueguen con la máquina. 3. Utilícela solamente como se describe en este manual de funcionamiento Dyson. No realice ningún otro mantenimiento que no sea el mostrado en este manual, o el recomendado por la línea de ayuda de servicio al cliente Dyson. 4. Adecuada SOLAMENTE para lugares secos. No utilice para aspirar agua u otros líquidos. 5. No utilice para aspirar agua u otros líquidos. 6. No manipule el enchufe o de la máquina con las manos mojadas. 7. No lo use si el cable o el enchufe están dañados. Si se ha dañado el cable de corriente, deberá ser reemplazado por Dyson, uno de sus representantes de servicio u otra persona igualmente capacitada a fin de evitar un peligro. 8. Si la máquina no funciona como es debido, ha recibido un golpe fuerte o se ha caído, dañado, dejado a la intemperie, o sumergido en agua, no lo utilice y comuníquese con la línea de ayuda de servicio al cliente Dyson. 9. Comuníquese con la línea de ayuda de servicio al cliente Dyson cuando se requiera mantenimiento o reparación. No desmonte la máquina, ya que un montaje incorrecto puede provocar descargas eléctricas o incendios. 10. No estire el cable ni permita que ejerza presión. Manténgalo alejado de superficies calientes. No apriete el cable cuando cierre la puerta ni tire del cable en bordes o puntas filosas. Acomode el cable de tal modo que quede alejado de áreas transitadas y lugares donde se lo pise o cause tropiezos. No pise el cable con la máquina. 11. No desconecte la máquina tirando del cable. Para desconectar, tome el enchufe y no el cable. No es recomendable utilizar una extensión de cable. 12. No aspire líquidos inflamables o combustibles como gasolina, ni la utilice en áreas dónde pueda haber este tipo de líquido. 13. No aspire nada que se esté quemando o que emita humo, como cigarrillos, fósforos o cenizas calientes. 14. Mantenga el cabello, ropa suelta, los dedos y cualquier otra parte del cuerpo alejados de las aberturas y de las partes móviles. No apunte con la manguera, la empuñadura o los accesorios a los ojos u orejas, ni se los meta en la boca. 15. No obstruya las aberturas de la máquina con ningún objeto. No utilice la máquina si tiene alguna abertura obstruida; manténgalas libres de polvo, pelusas, cabellos o cualquier otra cosa que pueda reducir la circulación del aire. 16. Utilice solamente los accesorios y las piezas de repuesto recomendadas por Dyson. 17. Para evitar un peligro de tropiezo, enrolle el cable cuando no este en uso. 18. No lo utilice si el compartimiento cubo transparente y el filtro no están colocados en su lugar. 4 19. No se aleje de la máquina si está conectato. Desconéctelo si no lo está usando y antes de darle servicio. 20. No utilice el cable para jalar o transortar la máquina, ni use el cable como si fuera una asa. 21. Tenga mucho cuidado cuando utilice la máquina sobre una escalera. No trabaje con la máquina por encima de usted en la escalera. 22. Apague todos los controles antes de desconectar. Desenchufe antes de conectar cualquier herramienta o accesorio. LEA Y GUARDE ESTAS INSTRUCCIONES ESTA MÁQUINA DYSON ES PARA USO DOMÉSTICO SOLAMENTE INSTRUCIONES DE POLARIZACIÓN Para disminuir el riesgo de choque eléctrico, esta máquina lleva un enchufe polarizado (una clavija es más ancha que la otra). Este enchufe se conecta a una toma de corriente polarizada de una sola forma. Si el enchufe no entra totalmente en la toma de corriente, dé la vuelta al enchufe. Si sigue sin entrar bien, póngase en contacto con un electricista calificado para instalar una toma de corriente correcta. No intente violar este dispositivo de seguridad, ni haga modificación alguna al enchufe. No jale el cable. No guarde la máquina cerca de fuentes de calor. No utilice la máquina cerca de una llama. No pise el cable con la máquina. No aspire agua o líquidos. No aspire objetos que se estén quemando. No utilice el aparato por encima de su cabeza si se encuentra sobre una escalera. No coloque las manos cerca del cepillo cuando el aparato esté en funcionamiento. 5 Operation Funcionamiento Storage Almacenamiento Emptying the clear bin Cómo vaciar el cubo transparente Looking for blockages Cómo buscar obstrucciones 6 iento Carrying the machine Para trasladar el aparato Carpets or hard floors Alfombras o pisos Tool attachments Accesorios de herramientas Brush bar clearing obstructions Cepillo: para eliminar obstrucciones x1 7 IMPORTANT! WASH FILTERS IMPORTANTE! LAVADO DE LOS FILTROS A B Base plate disassembly Mantenimiento del cepillo desarmar Base p Mante 8 ! S Wash filters with cold water at least every 3 months. The filters may require more frequent washing if vacuuming fine dust. Lave los filtros con agua fria al menos cada 3 meses. Si se aspira polvo fino, será necesario lavar el filtro con mayor frecuencia. Base plate reassembly Mantenimiento del cepillo armar 9 USING YOUR DYSON MACHINE PLEASE READ THE IMPORTANT SAFETY INSTRUCTIONS IN THIS DYSON OPERATING MANUAL BEFORE PROCEEDING. RATING PLATE Your serial number can be found on your rating plate which is behind the clear bin. Check to ensure your electricity supply corresponds to that shown on the rating plate. The machine must only be used as rated. ASSEMBLY Lie the machine on its back. Attach the cleaner head by sliding it on to the connections on the lower front part of the ball. Ensure the electrical plug on the cleaner head fits into the twin - block connection on the body of the machine, which is directly above the airway. Push firmly: the cleaner head will click into place. Stand the machine up straight. Attach the wand handle by sliding it on to the top of the machine. The spring clip in the handle will click into place. Ensure the hose is straight. Press the red button on the hose. Slide the wand into the hose. Ensure the wand and hose sit in the recess of the handle. Slide the end of the wand down into the handle to secure it. Close the wand cap. Slide the tool holder onto the side of the duct as shown. Ensure the cyclone and clear bin unit is secured to the main body of the machine. Attach the tools as shown. In use, the tools can be attached to either the hose or the wand. Wind the cable around the cable hooks. Secure with the clip. To watch a short online video visit: OPERATION Unwind the cable. Plug the machine into the mains electricity supply. To switch ON or OFF press the red power button, located as shown. To use, recline the handle. The stabilizer stand will automatically lift up. After use, return the machine to the upright position, pushing it firmly into place. The stabilizer wheels will automatically lower. Then unplug the machine, coil the cable safely and put the machine away. Switch 'OFF' the machine, unplug and ensure it is upright before: changing or using tools removing the hose or airway inspection parts. Use the cyclone carry handle to carry the machine. ATTACHMENTS To release the wand, open the wand cap and pull the red tube up and away from the handle until it clicks into place. Should you wish to use the hose without the wand, follow the above instruction and press the red button to release the wand from the hose. CARPETS OR HARD FLOORS The brush bar will always default to ON (spinning) each time you switch the machine ON and recline it for cleaning. The brush bar will not rotate when the machine is upright. To switch the brush bar 'OFF' (e.g. for delicate rugs and delicate flooring): switch the machine ON recline the machine press the brush bar ON/OFF button the brush bar will stop spinning. The brush bar will automatically stop if it becomes obstructed. See Brush bar clearing obstructions. Before vacuuming your flooring, rugs and carpets, check the manufacturer's recommended cleaning instructions. Some carpets may fuzz if a rotating brush bar is used when vacuuming. If this happens, we recommend vacuuming with the brush bar switched 'OFF' and consulting with the flooring manufacturer. The brush bar on the machine may damage some carpet types. If you are unsure, turn OFF the brush bar. Check the brush bar regularly and clear away any debris (such as hair). Debris left on the brush bar may cause damage to flooring when vacuuming. LOOKING AFTER YOUR DYSON MACHINE Do not carry out any maintenance or repair work other than that shown and described in this Dyson Operating Manual, or advised by the Dyson Helpline. Only use parts recommended by Dyson. If you do not this may invalidate your warranty. Store the machine indoors. Do not use or store it below 37.4 F (3 C). Ensure the machine is at room temperature before operating. Clean the machine only with a dry cloth. Do not use any lubricants, cleaning agents, polishes or air fresheners on any part of the machine. If used in a garage, always wipe the base plate and ball with a dry cloth after vacuuming to clean off any sand, dirt, or pebbles that could damage delicate floors. VACUUMING Do not use without the clear bin and filters in place. Fine dirt such as plaster dust or flour should only be vacuumed in very small amounts. Do not use the machine to pick up sharp hard objects, small toys, pins, paper clips, etc. They may damage the machine. When vacuuming, certain carpets may generate small static charges in the clear bin or wand. These are harmless and are not associated with the mains electricity supply. To minimize any effect from this (small static charge), do not put your hand or insert any object into the clear bin unless you have first emptied it and cleaned it with a damp cloth (see Cleaning the clear bin ). Do not work with the machine above you on the stairs. When cleaning stairs it is recommended that the handle is not extended and that you use a tool on the end of the hose rather than the wand. Do not put the machine on chairs, tables, etc. Before vacuuming highly polished floors, such as wood or linoleum, first check that the underside of the floor tool and its brushes are free from foreign objects that could cause marking. Do not leave the cleaner head in one place on delicate floors. Do not use this machine outdoors. The Dyson Car Cleaning Kit (Model 08909) is intended for use only inside a garage. EMPTYING THE CLEAR BIN Empty as soon as the dirt reaches the level of the MAX mark do not overfill. Switch OFF and unplug before emptying the clear bin. To remove the cyclone and clear bin unit, press down on the red button on the top of the carrying handle on the cyclone. To release the dirt, press all the way down on the same red button on the top of the carrying handle on the cyclone. To minimize dust/allergen contact when emptying, encase the clear bin tightly in a plastic bag and empty. Remove the clear bin carefully from the bag. Seal the bag tightly, dispose as normal. To refit: ensure the airway in the bin base is clear of dust and dirt close the clear bin base so it clicks into place push the cyclone and clear bin unit into the main body of the machine; it will click into place ensure the cyclone and clear bin unit is secure. WASHING YOUR FILTERS Your machine has two washable filters, located as shown. Check and wash the filters regularly according to instructions to maintain performance. Switch OFF and unplug before checking or removing the filters. The filters may require more frequent washing if vacuuming fine dust. Wash with cold water only. Do not use detergents. Do not put the filters in a dishwasher, washing machine, tumble dryer, oven, microwave or near a open flame. FILTER A Remove cyclone and clear bin (see 'Emptying the clear bin'). Release the catch on the front of the cyclone handle and then remove the filter. Wash the filter with cold water only. Hold under a tap and run water through the open end until the water runs clear. Turn upside down and tap out. Squeeze and twist with both hands to make sure the excess water is removed. Run water over the outside of the filter until the water runs clear. Squeeze and twist with both hands to make sure the excess water is removed. Stand the filter on its wide, open end to dry. Leave to dry completely for a minimum of 24 hours. Replace the filter into the cyclone. Swing the handle back into place. Ensure the latch clicks to engage and is secure. Fit the cyclone and clear bin unit onto the machine (instructions above). FILTER B Lie the machine on its side. To remove filter B: turn the blue central locking dial on the outer cover of the ball counter-clockwise until the cover is released lift off the cover turn the filter one-quarter counter-clockwise to release. Wash the filter with cold water only. Filter B should be rinsed and tapped out until the water runs clear, then tapped out again to ensure all excess water is removed. (Tap on the plastic rim, not the filter material.) Leave to dry completely for a minimum of 24 hours. It is normal for the filter in the ball to turn gray in color. To refit filter B: 10 refit the filter on to the ball secure the filter by turning it clockwise so the white arrows align. When refitting the outer cover of the ball, keep turning the central locking dial clockwise. When it starts to click it is locked. To watch a short online video visit: BLOCKAGES THERMAL CUT-OUT This machine is fitted with an automatically resetting thermal cut-out. Large items may block the tools or wand inlet. If any part becomes blocked the machine may overheat and automatically cut-out. If this happens, follow the instructions below in 'Looking for blockages'. LOOKING FOR BLOCKAGES Switch OFF and unplug before looking for blockages. Failure to do so could result in personal injury. Leave to cool down for 1-2 hours before checking the filters or for blockages. Clear any blockage before restarting. Look for blockages in the wand, airways and cleaner head. To release the hose from the machine, you will need to remove the wand. Open the wand release cap. Pull the wand up and away from the handle. Press the red release button in the connecting collar and remove the wand from the hose. Remove the clear bin and cyclone unit. Then release the hose from the machine by pressing the red tab on the base of the hose you can see it from the front of the machine. Check for blockages in the hose. Beware of sharp objects when checking for blockages. To refit the hose, align the guides on the base of the hose with the channels in the neck of the airway. Ensure the red tab faces the front of the machine. Push the hose on. It will click into place. To refit the wand follow the instruct
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks
SAVE OUR EARTH

We need your sign to support Project to invent "SMART AND CONTROLLABLE REFLECTIVE BALLOONS" to cover the Sun and Save Our Earth.

More details...

Sign Now!

We are very appreciated for your Prompt Action!

x